This text is a copy of the  manual given to students who want to build their own MicroLab. They receive this manual, the components, the PCB (printed Circuit Board) and the (programmed) processor.

This manual explains how to build the MicroLab yourself. It also mentions the important issues for building a good and relatively cheap MicroLab, which will function perfectly, when built correctly. The “Microlab building pack” comes together with a Printed Circuit Board (PCB), manual and the RISC-processor PIC16C73. This processor is fully programmed and ready to go. The only thing you have to do is to assemble the PCB and mount it into a cabinet of your choice. It is quite easy to build and complete the PCB. Just double-check everything you do before soldering the components onto the PCB.  If you are NOT sure, do NOT slder, but first think again.
It's a nasty job to remove soldered components!

If a chip is connected the wrong way, the circuit will NOT work and you can damage the chip and the total circuit when power is applied!

H1, H2, H3, H4                           10-pins header (Analog in)
The pins on the outside are connected to the power. The remaining pins are the inputs. This means 8 x 4 inputs in total. From these 32 inputs you can solder wires to a connector of your choice.

J1                                              5-pins header (MIDI out)
The MIDI output is connected with 3 wires. The header-pin, which is directly connected to R3, has to be connected to pin 4 of the MIDI DIN connector. The header-pin, which is directly connected to R2, has to be connected to pin 5 of the MIDI DI connector. Pin 2 of the MIDI-connector is ground (see schematic!).                  

J2                                              2-pins header (Jumper setting J2)
This jumper (is a direct connection, or shortcut) determines the "base-address" of the MIDI controllers. If J2 has a jumper (shortcut) the controller’s numbers starts at 20. If J2 does NOT have a jumper (open), the controller number starts at 0.

J4                                              4-pins header (Jumper setting J4)
A jumper must be connected over the middle two pins (shortcut between pin 2 and 3). This is necessary for the Ultrasonic distance measuring to function ok. The fact that 4 pins header is used, has got to do with former MicroLab versions.

J6                                              8-pins header (key-scan 4x4)
This is the connection for the 16-input key scan. The pins directly connected to pins 25, 26, 27 and 28 are the Matrix Inputs (Mat_in). The other four are the Matrix Outputs (Mat_out). The appendix shows a schematic of the keyboard connections.

J7                                              4-pins header (switch inputs)
On these 4 pins a switch can be connected. A closed switch generates controller MIDI, value 127. An open switch generates controller MIDI value 0.

J8, J9                                         2-pins header (Ultrasonic output)
The Ultrasonic Transmitter has to be connected to these pins (often the S from Sender is written on the Transmitter). There are two headers: one normal 40 kHz signal and one 40 kHz signal inverted. The transmitter has to be connected to both. Always use shielded wire

J10                                            2- pins header (Ultrasonic input)
The Ultrasonic receiver connection : One pin to ground and one pin to the signal. The R from Receiver is written down on the receiver itself (receiver and transmitter look alike!). Always use shielded wire.

J12                                            2-pins header (Power/batt connection)
Connection for the power supply or 9V battery. The power-supply at this point has to be between 7V-12V DC. Check the polarity! The pin closest to the black diode (D10) is the positive (+) connection.

  X1                          (X-tal 18.432 MHz version 4.x / X-tal 20MHz version 5.xF)
This is a Crystal Oscillator. This component generates the clock for the processor. Without this component the microlab will NOT work. It's important that the exact frequency is used (18.432 MHz), otherwise the MIDI will not have the right timing! Do not mount the Crystal directly on the board, but leave (1mm) space between the Crystal and the PCB.

  SW1                                          2-pins header (Reset switch)
Connect a simple switch (make contact) to this header. It generates a total reset for the processor.

Before connecting the power to the Microlab PCB, it's better to check the following.
Take a close look at the solder-side of the PCB and make sure that there are NO Shortcuts.

Check the polarity of the capacitors.
Check the "pin 1" of all the IC's
Check the polarity of all diodes.

When you connect the MicroLab for the first time you will need some devices to measure the exact power (+5V) and to adjust the frequency of the Ultrasonic circuit. For measuring the power you will need a simple voltmeter. For measuring and adjusting the frequency an oscilloscope or frequency-counter will come in handy.  When you are sure everything is correct, connect the power (+7-15 V DC) on jumper J12. The testing of the MicroLab is actually simple. To make it easier, the circuit has 5 Test Points (TP1 till TP5). Start with TP1 and end with TP5.

TP1 : At this point you should (if power is connected) measure the power-supply. This must be a positive DC-voltage with a value between a minimum +7V and a maximum of +18V. When connecting a battery, you should measure 9V DC. When the value is beneath 7V DC, the circuit will not work.

TP2: This is the power for the circuit and is measured after the voltage regulator (U6). This DC-value must be +5V (4,75 - 5,25). If this value is higher, you must disconnect the power immediately! When the DC-value is lower than 5V it is likely that there is a shortcut somewhere. Disconnect the power (or battery) and check the entire above once more.

TP3 (U1 / pin 21,22,23,24): When you are sure the power-supply is correct, you can connect a probe from a oscilloscope to TP3. At this point you should see a square-wave. If there is NO square-wave, the processor is NOT working. At this point you could measure the DC-value of "pin 1" (reset) from the processor. This pin should be "high"; meaning the value is +5V. If this value is below +5V, the processor is in active (reset-mode) and will not work. Check C1! If you do see a square-wave, it means that the software inside the processor function ok.

TP4 (U3 / pin 3): If you want to use the ultrasonic distance measuring as well, you have to test / adjust the 80 kHz frequency, generated by the timer chip U8. Make sure (for the testing) that NO jumpers are connected on J4! Connect a probe (from a oscilloscope) to TP4. You should see a square-wave. Take a small screwdriver and adjust the frequency to 80 kHz exact. If the 80 kHz works fine, connect the jumper on J4 in the middle-position.

TP 5 (U1 / pin 17): On pin 17 of the processor you can check whether MIDI is produced. Connect the probe and touch one of the headers H1 till H4 with your finger. This should produce MIDI. If you already connected the LED (D1), the MIDI should also be visual.

Inputs:
32 inputs in total. This is realized with two HEF4067 chips, both having sixteen inputs. Which input represents which MIDI controller number, can be seen on the right figure. From all 10 ins headers, the outside pin is NOT connected (see left figure). The outside pins on the both headers in the middle (see left figure) are connected to the power supply; ground(-)  and 5V (+)

In the three figures above, you can see how the inputs of the Microlab can be connected. In total there are 4 times 10 pins headers available for input. This means 40 pins! The outside pins of all four headers are no inputs. Means there are 32 inputs left to connect. The numbers in the picture on the right show which controller numbers represents which pin. 

The connections given below are not a MUST. You can connect the inputs to the Sub D connectors as you like. It is of course convenient if you connect it the same way, so you can exchange Microlab's if nessecary.
Note 1: Pin 1 of the 37p Sub D connector is connected to controller input number one. The first MIDI controller numer is 0. This input is connected to pin 32.
Note 2: The connections of the Keyboard Matrix are also linked to the pins of the processor. Four of these connections are not directly linked to the chip, but through a resistor array. It's just a indication!

Because of some practical reasons, we decided to use the 'left over pins' of the processor as extra switch inputs. This means the four pins are connected to vcc with an external resistor. When connected to ground, through a switch, the processor will generate midi value 0; if released again, midi value 127 is generated.

switch 1: midi controller number 64
switch 2:  midi controller number 65
switch 3:  midi controller number 66
switch 4:  midi controller number 67

The main output is MIDI. As mentioned before the output pins of the pic16c73 can deliver enough current to supply a MIDI loop, but we chose to connect a port in between. Just to be on the safe side. As shown in the schematic, midi is coming from pin 17 (RC6). From that point it drives two ttl ports from the 74LS09. One port is connected to the standard midi din plug (j1) and provides the midi current loop. The other port is driving a little led, to have an indication that midi has been put out.

Jumper J2 drawn in between determines the midi controller value offset. If the jumper is connected (connection to ground has been made), the controller value's will start with midi number 20. If the jumper is not connected (pin 15 stays 'high') the midi controller values will start with 0.

(back to the top)